3-19-00 Propeller
Early Part Number Late Part Number Description Price Core Charge
3-19-01 3-19-01 PROPELLER DRIVE SHAFT HOUSING, LEFT SIDE-Goes on outside rear floor with propeller shaft and propeller fitting on it. $274.41 $0.00
None 3-19-01a PROPELLER DRIVE SHAFT HOUSING, RIGHT SIDE-Same as above, except right side. $274.41 $0.00
3-19-02 3-19-02 TAPER BALL BEARING-Fits on front of propeller drive shaft where it enters the rear engine compartment. $37.29 $0.00
3-19-03 3-19-03 PROPELLER DRIVE SHAFT-Propeller fits on rear end of this shaft with front part of shaft going through hull body into engine compartment. $229.41 $0.00
3-19-04 3-19-04 LOCKING CIRCLIP-Four are used on each propeller shaft with one on each side of bearings 3-17-72 and 3-19-05. $1.59 $0.00
3-19-05 3-19-05 CYLINDRICAL ROLLER BEARING-Fits next to propeller at rear of propeller shaft. $39.61 $0.00
3-19-06 3-19-06 LOCKING CIRCLIP-Three are used on each propeller shaft with two locking the two rear installed oil seals 3-19-09 and one behind the front installed seal 3-19-09. $4.73 $0.00
3-19-07 3-19-07 WASHER-Provides proper tension for propeller shaft bearings. $9.81 $0.00
3-19-08 3-19-08 SPACER WASHER-To provide proper positioning of shaft in housing. $6.27 $0.00
3-19-09 3-19-09 OIL SEAL FOR PROPELLER SHAFT-This seal keeps water from leaking into car by the propeller. Three are used per shaft with one in front and two in back at the propeller end. $18.55 $0.00
3-19-10 3-19-10 KEYWAY-Keeps propeller from spinning free on axle shaft. $6.12 $0.00
3-19-11 3-19-11 NEW ORIGINAL AMPHICAR PROPELLER-Shiny-white polypropolethylene, original Amphicar. $159.30 $0.00
3-19-12 3-19-12 SPACER-Fits behind propeller, correctly positioning propeller on shaft. $6.75 $0.00
3-19-13 3-19-13 WHITE PROPELLER HUB NUT-Large, cone-shaped nut tightens propeller on shaft. $23.49 $0.00
3-19-14 3-19-14 SCREW-For propeller. $0.55 $0.00
3-19-15 3-19-15 GREASE FITTING-For lubrication of rear propeller bearing. $1.90 $0.00
3-19-16 3-19-16 OVAL PROPELLER HOUSING GASKET-Seals propeller housing 3-19-0l/0la against hull. $23.21 $0.00
3-19-17 3-19-17 BOLT-To mount propeller housing on body. $0.49 $0.00
3-19-18 3-19-18 NYLON WATER SEALING WASHER-When bolt is tightened against this "dubo" washer, it creates a waterproof seal. Eight used per propeller housing. $1.39 $0.00
3-19-19 3-19-19 RETAINING RING WASHER-Holds above nylon washer in place when tightened down. $1.21 $0.00
3-19-20 3-19-20 NUT-With above bolt 3-19-17, mounts propeller housing on body. $0.36 $0.00
3-19-21 3-19-21 LEG GASKET-Seals the "legs" of the propeller housing 3-19-0l/0a against the hull. Gasket is about one inch square. $3.30 $0.00
3-19-22 3-19-22 UNIVERSAL JOINT PROPELLER SHAFT ASSEMBLY-Two per water transmission. One end fastens to back of water transmission end other end has spline opening to slide on propeller shaft in engine compartment. $379.85 $0.00
3-19-22KIT 3-19-22KIT PROPELLER SHAFT U-JOINT REPAIR KIT-Replaces worn u-joints at either end of propeller shaft. Original Amphicar production u-joints do not have grease each fittings this joint does. If your transmission vibrates in the water, replace the bad u-joints to avoid damage to the water transmission. Two needed per shaft. $51.08 $0.00
3-19-23 3-19-23 STAR ALLEN SCREW-Four used per propeller u-joint shaft to hold flange and shaft on water transmission drive stub. $0.81 $0.00
None 3-19-23T SOCKET ALLEN WRENCH-Two inch long allen extension for 3/8" socket wrench. $32.70 $0.00
3-19-24 3-19-24/25 TOOTH WASHER-To mount u-joint shaft on transmission. Also used to mount legs of propeller housing on body. $0.28 $0.00
None 3-19-26 FLAT WASHER-Used under tooth washer 3-19-25 for extra support where propeller housing legs are fastened to body. $0.28 $0.00
None 3-19-23T SOCKET ALLEN WRENCH-Two inch long allen extension for 3/8" socket wrench. $33.33 $0.00