| Early Part Number | Late Part Number | Description | Price | Core Charge |
|---|---|---|---|---|
| 10-32-03 | 10-32-03 | RETAINING SPRING CLIP-Holds headlight rim water seal against inside of chrome rim. | $1.39 | $0.00 |
| None | 10-32-04 | OUTER VINYL SEAL FOR CHROME HEADLIGHT RIM-This is the soft, pliable, molded seal which is clip-held inside chrome rim with seal lip exposed on outside against sealed beam retainer. Note: If you have not replaced this seal, it will be hard and will most li | $34.13 | $0.00 |
| 10-32-06 | 10-32-05 | HEADLIGHT RIM-Chrome replacement to the original rim. This is not 100% identical, but fastens exactly as the original. An inexpensive way to new looking headlights. | $43.97 | $0.00 |
| 10-32-04 | 10-32-13b | PRESSURE VALVE-Metal valve for bottom of headlight rim. Original Amphicar. | $9.51 | $0.00 |
| 10-32-05 | 10-32-13c | RUBBER VALVE COVER-Goes around pressure valve and keeps it on headlight rim. | $4.55 | $0.00 |
| 10-32-08R | 10-32-07R | CHROME INSIDE GLASS HOLDING RING-Sits behind chrome rim and holds sealed beam to adjusting ring, refurbished original design. | $24.97 | $0.00 |
| 10-32-09 | 10-32-08 | ADJUSTING RING-Sealed beam fits against this ring. It is fastened to headlight bucket by two adjusting screws and a tension spring. | $89.50 | $0.00 |
| None | 10-32-08R | ADJUSTING RING REPLACEMENT-Identical to above with minor modifications. | $25.49 | $0.00 |
| None | 10-32-10H | HALOGEN HEADLIGHT SEALED BEAM-. | $14.95 | $0.00 |
| 10-32-11 | 10-32-11 | HEAD LIGHT PRONG CONNETOR-3 way wire end connector snaps on sealed beam spring type. | $6.19 | $0.00 |
| None | 10-32-11B | HEADLIGHT PRONG CONNECTOR-Bullet type (9-98). | $0.00 | |
| 10-32-12 | 10-32-12R | HEADLIGHT BUCKET-Shell or "bucket" shape, with center hole for clamp bolt and hole for wire seal grommet. Requires installation of three "L" brackets for either original 10-32-08 adjusting ring or 10-32-08R replacement listed above. | $94.36 | $0.00 |
| None | 10-32-12a | CABLE SEAL-Seals headlight wires where they enter headlight bucket. | $4.37 | $0.00 |
| None | 10-32-12b | NUT-For headlight bucket bracket bolt. | $0.31 | $0.00 |
| None | 10-32-12c | BOLT-To fasten headlight bucket on body. | $0.50 | $0.00 |
| None | 10-32-12d | SUPPORT WASHER-For above bolt 10-32-12c. | $0.25 | $0.00 |
| None | 10-32-12e | SEAL, HEADLIGHT BUCKET TO BODY-Original Amphicar type. Two needed per car. | $8.60 | $0.00 |
| None | 10-32-13 | CHROME SCREW TO MOUNT HEAD LAMP RIM -Original chrome screw to secure rim on headlight bucket. | $0.99 | $0.00 |
| None | 10-32-14a | BULB SOCKET FOR FRONT MARINE LIGHT LENS. | $94.90 | $0.00 |
| None | 10-32-15 | FRONT MARINE LIGHT LENS- New production red/green lens. Goes on hood. | $159.95 | $0.00 |
| None | 10-32-15MB | FRONT MARINE LIGHT LENS-Reproduction red/green lens. Goes on hood. | $149.95 | $0.00 |
| None | 10-32-15a | CHROME SCREW-Fastens red/green lens to bulb receptacle. | $0.67 | $0.00 |
| None | 10-32-15b | RUBBER WASHER-Between bulb receptacle and red/green lens. | $0.25 | $0.00 |
| None | 10-32-15c | GASKET SEAL BASE-Fits around base of front marine light lens to keep water out of light assembly. If seal is defective, moisture will damage the chrome, red and green coatings on the interior side of the marine light lens. | $35.65 | $0.00 |
| None | 10-32-15cR | GASKET SEAL BASE-Replacement for above base. | $18.35 | $0.00 |
| None | 10-32-15d | NUT-Goes on bulb receptacle stud inside hood and propeller lamp bolt 10-32-33. | $0.25 | $0.00 |
| None | 10-32-15e | TOOTH WASHER-For above nut 10-32-15d. | $0.25 | $0.00 |
| None | 10-32-15f | RED INSULATING WASHER-Used on 1965-1967 Amphicars where front marine light can only be "on" when propeller shift lever is in forward or reverse. Goes on bulb receptacle stub before fastening ground wire to stud. | $0.43 | $0.00 |
| None | 10-32-15PS | PROTECTION SHIELD. | $7.95 | $0.00 |
| 10-32-16/10-32-57 | 10-32-16/10-32-46 | BULB- rear marine pole light, back-up light, and front parking light turn signal. | $0.99 | $0.00 |
| None | 10-32-16a | BULB-Low watt bulb for front marine light. | $0.98 | $0.00 |
| None | 10-32-17a | PARKING TURN SIGNAL LIGHT ASSEMBLY-Includes original amber bullet lens and bulb socket assembly, as installed on late Amphicars. | $65.71 | $0.00 |
| 10-32-18 | 10-32-18 | PARKING TURN SIGNAL LIGHT LENS-Original CLEAR Amphicar early lens, excluding chrome frame. | $49.90 | $0.00 |
| None | 10-32-18a | CHROME RING FRAME-For parking light lens. | $15.50 | $0.00 |
| None | 10-32-18bRB | BLACK TURN SIGNAL LAMP LENS GASKET-Replacement for original base gasket. Sold as continuous strip which is glued to outer edge of chrome lens rim with hot melt or Crazy glue. Provides proper lens-to body sealing with decorative edge identical to original To seal bulb socket screws and wire opening, use any generaic flat rubber. | $5.22 | $0.00 |
| None | 10-32-18bRW | WHITE TURN SIGNAL LAMP LENS GASKET-Same as above, except is white. | $5.22 | $0.00 |
| None | 10-32-18c | INNER-SEAL-Fits into grove between turn signal lens and chrome rim to provide additional sealing along with base 10-32-18bRB/W. | $3.50 | $0.00 |
| None | 10-32-18d | CHROME SCREW-Two needed to fasten parking light lens on bulb receptacle base. | $1.01 | $0.00 |
| None | 10-32-18e | SCREW-Fastens parking light bulb receptacle base on body. | $0.31 | $0.00 |
| None | 10-32-18Y | PARKING TURN SIGNAL LIGHT LENS-Amber bullet lens for parking turn signal light assembly 10-32-17a. | $42.25 | $0.00 |
| 10-32-19 | 10-32-19 | BULB-Small lower parking/running light bulb. Also used in license plate lamp. | $0.98 | $0.00 |
| 10-32-20 | 10-32-20 | DIMMER SWITCH-Original Amphicar. | $6.75 | $0.00 |
| 10-32-21 | 10-32-21 | SCREW-To fasten dimmer switch to toe board. | $0.31 | $0.00 |
| 10-32-22 | 10-32-22 | TOOTH WASHER-For screw 10-32-21. | $0.25 | $0.00 |
| 10-32-23 | 10-32-23 | HORN-Replacement horn identical to original horn. Mounts on all brackets exactly as original. Modification required: drill holes in outer housing to fasten cover. | $41.67 | $0.00 |
| 10-32-23C | 10-32-23C | HORN CHROME COVER-Original chrome outer cover for horn assembly. | $59.15 | $0.00 |
| None | 10-32-23CB | HORN TRIM BADGE. | $16.45 | $0.00 |
| 10-32-24 | 10-32 24R | HORN BODY-Sheet metal round formed body. Horn mounts inside. | $41.51 | $0.00 |
| 10-32-25 | 10-32-25 | HORN BRACKET-Horn mounts on top of this bracket, bottom of bracket fastens to underside of hood. | $12.79 | $0.00 |
| 10-32-26 | 10-32-26 | BOLT-Mounts horn bracket to fixture on underside of hood. | $0.49 | $0.00 |
| None | 10-32-27 | NUT-With bolt 10-32-26 and with other horn brackets. | $0.31 | $0.00 |
| None | 10-32-28 | TOOTH WASHER-For horn bracket at horn. | $0.25 | $0.00 |
| None | 10-32-29 | LOCK WASHER-For horn bracket to hood. | $0.25 | $0.00 |
| 10-32-30 | 10-32-30 | LICENSE PLATE LAMP ASSEMBLY-Two are mounted above license plate on rear deck lid includes mounting screws and oval seal ring. | $47.11 | $0.00 |
| None | 10-32-30/1 | LICENSE PLATE LAMP ASSEMBLY-Same as above, except minor blemished or used. | $18.81 | $0.00 |
| None | 10-32-30L | LICENSE PLATE LAMP LENS. | $31.30 | $0.00 |
| 10-32-31 | 10-32-31 | SCREW-Two required to fasten license plate lamp on engine cover. | $0.31 | $0.00 |
| 10-32-32 | 10-32-32 | CONTROL SWITCH-Mounts on water transmission lever shaft under rear seat. When you move water transmission lever forward or reverse, this switch turns on orange propeller indicator light on dash. | $41.23 | $0.00 |
| 10-32-44 | 10-32-33 | BOLT-To fasten marine control switch 10-32-32 on body. | $0.25 | $0.00 |
| 10-32-45 | 10-32-33a | LOCK WASHER-For bolt 10-32-33. | $0.25 | $0.00 |
| None | 10-32-33c | CHROME SCREW-Six required to fasten chrome horn cover on horn body. | $0.65 | $0.00 |
| None | 10-32-34 | REAR MARINE POLE LIGHT ASSEMBLY-Includes chrome mast with clear lens assembly on top and contact pin on bottom, original Amphicar. Supplied on 1960 early 1967 cars. | $179.90 | $0.00 |
| None | 10-32-34e | ECONOMY REAR MARINE POLE LIGHT ASSEMBLY-Same as above, except has minor blemish. | $150.85 | $0.00 |
| None | 10-32-34L | REAR MARINE POLE LIGHT ASSEMBLY, LONG VERSION-Same as above, except chrome mast is twice as high, original Amphicar. Supplied on late model 1967 cars. | $275.05 | $0.00 |
| 10-32-34 | 10-32-35 | GLASS LENS-For rear marine pole light assembly. | $61.93 | $0.00 |
| None | 10-32-35a | RUBBER GASKET-To seal glass lens on pole light. | $3.79 | $0.00 |
| None | 10-32-35b | LENS CHROME RING-Mounts rear pole light lens on top of pole. | $29.95 | $0.00 |
| None | 10-32-35c | CHROME POLE TUBE-At on end, light assembly is fastened and at the other end, pin contact switch 10-32-35d is fastened. | $50.05 | $0.00 |
| 10-32-36 | 10-32-35d | PIN CONTACT SWITCH-Screws into bottom of pole light. | $55.42 | $0.00 |
| None | 10-32-35e | GASKET-To seal pole light to glass lens. | $3.66 | $0.00 |
| 10-32-53 | 10-32-36 | MOUNTING BRACKET-Holds back-up light switch on front of water transmission. | $8.70 | $0.00 |
| None | 10-32-36a | LEATHER STRAP-To hold rear pole light on rear seat back brace. | $5.41 | $0.00 |
| None | 10-32-36b | ANTI-RATTLE RUBBER STRIP-Glues to rear seat back metal brace to prevent pole light from vibrating. | $0.62 | $0.00 |
| None | 10-32-36c | CHROME SCREW-Fastens leather strap 10-32-36a to rear seat back brace. | $0.66 | $0.00 |
| None | 10-32-36d | CHROME DRESS WASHER-Supports chrome screw 10-32-36c on leather strap. | $0.69 | $0.00 |
| None | 10-32-36e | NUT-For screw 10-32-36d. | $0.25 | $0.00 |
| None | 10-32-36f | LOCK WASHER-For screw 10-32-36d. | $0.25 | $0.00 |
| 10-32-37 | 10-32-37 | TAILLIGHT LENS ASSEMBLY-Includes red lens, chrome reflecting shell with bulb socket and rubber seal base. | $79.95 | $0.00 |
| 10-32-38 | 10-32-38 | TAILLIGHT LENS. | $65.71 | $0.00 |
| None | 10-32-39 | CHROME REFLECTOR SHELL-With bulb socket. | $29.98 | $0.00 |
| 10-32-39 | 10-32-39a | RUBBER SEAL BASE-Seals taillight lens on car body. | $45.84 | $0.00 |
| None | 10-32-39b | CHROME SCREW-Two required to fasten taillight assembly on car. | $2.85 | $0.00 |
| None | 10-32-39c | RUBBER WASHER-Goes behind taillight lens on end of chrome screw 10-32-39b. | $0.24 | $0.00 |
| 10-32-40 | 10-32-40 | BULB FOR TAILLIGHT ASSEMBLY-Two way brake and taillight, original Amphicar. | $0.99 | $0.00 |
| 10-32-41 | 10-32-41 | BACK-UP LIGHT ASSEMBLY COMPLETE-Original Amphicar. Includes clear lens, bulb socket base, gray rubber seal base, mounting nut, washer, and wire boot. | $155.07 | $0.00 |
| 10-32-42 | 10-32-42 | BACK-UP LIGHT LENS-Original Amphicar. | $54.55 | $0.00 |
| None | 10-32-43RB | RUBBER SEAL. BLACK-Replaces original base gasket. Sold as continuous strip to surround lens, it glues to outer edge with hot melt or Crazy glue. Provides proper lens-to-body sealing with decorative edge identical to original. To seal bulb socket beneath lens, use any generic rubber sheet. | $5.22 | $0.00 |
| None | 10-32-43RW | RUBBER SEAL, WHITE Same as above, except white. | $5.22 | $0.00 |
| None | 10-32-44 | CHROME SCREW-Holds back-up light lens on car, two required. Same as 11-39-17. | $0.69 | $0.00 |
| 10-32-44 | 10-32-33 | BOLT-To fasten marine control switch 10-32-32 on body. | $0.25 | $0.00 |
| 10-32-45 | 10-32-33a | LOCK WASHER-For bolt 10-32-33. | $0.25 | $0.00 |
| 10-32-16/10-32-57 | 10-32-46/10-32-16 | BULB-For back-up light, rear marine pole light and front parking light turn signal. | $0.99 | $0.00 |
| None | 10-32-46a | BULB-Low wattage for front marine light. | $0.97 | $0.00 |
| None | 10-32-47 | CLAMP FOR PROPELLER SWITCH-Clamps on rear of water transmission rod 11-44-12 under rear seat. Hole on clamp extension pivots propeller switch 10-32-32 on and off. | $5.37 | $0.00 |
| 10-32-48 | 10-32-48 | RUBBER HORN NECK-Seals horn shell on hood. | $19.95 | $0.00 |
| None | 10-32-48R | REPLACEMENT RUBBER HORN NECK-Identical to original, except does not have the side "saddle" curves which are hidden inside horn body. Since the curves serve no real purpose, this is an ideal cost saver. | $7.31 | $0.00 |
| 10-32-49 | 10-32-49 | METAL VENT PIPE-Fastens to horn bracket. Rubber vent hose from gas tank fits on bottom of this pipe. Top of vent pipe is inside horn shell. | $18.72 | $0.00 |
| 10-32-50 | 10-32-50 | VENT HOSE-Fuel tank to horn metal pipe. | $1.49 | $0.00 |
| 10-32-51 | 10-32-51 | BACK-UP LIGHT SWITCH-Goes under rear seat. | $44.29 | $0.00 |
| None | 10-32-51a | RUBBER GROMMET-Seals back-up light switch where wires enter switch. | $0.58 | $0.00 |
| 10-32-52 | 10-32-36 | MOUNTING BRACKET-See late part number 10-32-36 above. | $8.70 | $0.00 |
| 10-32-53 | 10-32-53 | LINKAGE-Wire-like piece from back-up light switch to transmission lever. | $2.22 | $0.00 |
| 10-32-54 | 10-32-54 | SCREW-Two used to fasten back-up light switch on bracket. | $0.25 | $0.00 |
| 10-32-55 | 10-32-55 | NUT-For screw 10-32-54. | $0.25 | $0.00 |
| 10-32-56 | 10-32-56 | LOCK WASHER-For screw 10-32-54. | $0.25 | $0.00 |
| None | 10-32-57 | INTERIOR LIGHT ASSEMBLY-Mounts under dash below glove box, original Amphicar. | $29.91 | $0.00 |
| None | 10-32-57aR | INTERIOR LENS. | $18.15 | $0.00 |
| None | 10-32-58 | BULB-For interior light. Horizontal tube type bulb. | $2.49 | $0.00 |
| None | 10-32-59 | SCREW-To fasten interior lamp assembly on dash under glove box. | $0.25 | $0.00 |