1-07-00 Carburetor
| Early
Part Number |
Late
Part Number |
Description |
Price |
Core
Charge |
| 1-07-01 |
1-07-01 |
CARBURETOR
COMPLETE-Original Zenith/Solex carburetor, identical to original
Amphicar carburetor. Plus core charge of $25.00, which is refunded when
you mail us your old carburetor. |
$247.65 |
$25.00 |
| None |
1-07-01R |
REBUILT
CARBURETOR COMPLETE-Same as above, except rebuilt. Core charge of
$25.00. |
$279.00 |
$25.00 |
| None |
1-07-01S |
SPRAYER. |
$17.50 |
$0.00 |
| 1-07-02 |
1-07-02 |
THROTTLE
PLATE-About the size of a quarter. It rotates back and forth on bottom
of carburetor. |
$12.79 |
$0.00 |
| None |
1-07-03 |
THROTTLE
SHAFT-Brass shaft oscillates plate 1-07-02. |
$31.79 |
$0.00 |
| 1-07-04 |
1-07-04 |
SCREW
FOR THROTTLE PLATE-See description under 1-07-22. |
$4.25 |
$0.00 |
| 1-07-05 |
1-07-05 |
WASHER
FOR THROTTLE SHAFT-About the size of a dime, this washer with
rectangular hole in the center, slides on the throttle shaft and stops
the idle speed plate 1-07-06 from touching choke advance plate 1-07-14. |
$2.99 |
$0.00 |
| 1-07-06 |
1-07-06 |
IDLE
SPEED STOP PLATE-Pivots on throttle shaft 1-07-03. Screw 1-06-07 adjusts
idle speed. |
$7.07 |
$0.00 |
| 1-07-07 |
1-07-07 |
IDLE
SPEED ADJUSTMENT SCREW-This is the normal steel screw which controls the
r.p.m. or "idle speed" of your engine, once you've fine-tuned
your carburetor and distributor. Here's an emergency tip: if your
accelerator cable ever breaks on your way from can tighten down the
screw to increase your engine speed to give you enough speed to get to a
repair shop. |
$3.96 |
$0.00 |
| 1-07-08 |
1-07-08 |
TENSION
SPRING-The above idle speed screw 1-07-07 goes into this spring,
providing enough tension to "lock" the screw at whatever speed
you select. |
$0.37 |
$0.00 |
| None |
1-07-09 |
LEVER- |
$5.95 |
$0.00 |
| 1-07-10 |
1-07-10 |
THROTLE
SHAFT END NUT-Tightens on end of the throttle shaft on the outside of
the carburetor, holding the accelerator connecting rod bracket on the
shaft. |
$3.96 |
$0.00 |
| 1-07-11 |
1-07-11 |
ACCELERATOR
PUMP CONTROL ROD-One end has 900 angle bend with threads which screws
into back of throttle shaft. Other end has clip slots and goes into
accelerator pump arm. Every time you step on the gas, this rod pivots
the accelerator pump arm to squirt gas into your carburetor. |
$11.45 |
$0.00 |
| 1-07-12 |
1-07-12 |
IDEL
SMOOTHNESS SCREW-This is the brass pointed screw which adjusts your
carburetor to get the smoothest possible idle speed. It goes into the
carburetor on the right lower side at as angle. |
$8.25 |
$0.00 |
| 1-07-13 |
1-07-13 |
TENSION
SPRING-For above smoothness screw 1-07-12. |
$0.37 |
$0.00 |
| None |
1-07-13a |
CHOKE
SPEED LEVER ASSEMBLY-This assembly automatically increases the speed of
your engine when you pull-out your choke cable. It contains all parts
1-07-14 through 1-07-18. |
$29.71 |
$0.00 |
| 1-07-14 |
1-07-14 |
CHOKE
SPEED BRACKET ON THROTTLE SHAFT |
$12.39 |
$0.00 |
| 1-07-15 |
1-07-15 |
CHOKE
SPEED LEVER ROD-This elbow rod connects at one end to 1-07-14 and other
end to choke cam. |
$4.15 |
$0.00 |
| 1-07-16 |
1-07-16 |
HOLDING
WASHER-For rod 1-07-15. Two required for rod. |
$0.36 |
$0.00 |
| 1-07-17 |
1-07-17 |
SPRING
FOR ROD-Goes between the two holding washers 1-07-16. |
$0.36 |
$0.00 |
| 1-07-18 |
1-07-18 |
COTTER
PIN-Keeps holding washers in place on rod 1-07-15. |
$0.36 |
$0.00 |
| 1-07-19 |
1-07-19 |
ACCELERATOR
PUMP SPRING-Goes inside accelerator pump diaphragm housing to return
diaphragm each time you step on gas. |
$6.31 |
$0.00 |
| 1-07-20 |
1-07-20 |
ACCELERATOR
PUMP DIAPHRAGM-About one inch square gasket held on by four screws at
right rear of carburetor. If this is broken, gas drips out on exhaust
manifold. |
$11.66 |
$0.00 |
| 1-07-21 |
1-07-21 |
HOUSING
WITH PIVOT ARM-For accelerator pump diaphragm. |
$41.15 |
$0.00 |
| 1-07-22 |
1-07-22 |
BRASS
SCREW-For needed to hold accelerator pump housing on carburetor. Can
also be used as screw 1-07-04 to hold throttle plate on throttle shaft,
if the screws are filed down. |
$4.15 |
$0.00 |
| 1-07-23 |
1-07-23 |
RETURN
SPRING-For accelerator pump control rod 1-07-11. |
$6.17 |
$0.00 |
| 1-07-25 |
1-07-25 |
MAIN
CONTROL BRACKET-Fits along entire right side of carburetor. Following
parts fasten to it: choke cable, choke cam and return spring. |
$25.56 |
$0.00 |
| 1-07-26 |
1-07-26 |
SCREW-Holds
rear of main control bracket 1-07-25 on carburetor. |
$1.83 |
$0.00 |
| 1-07-27 |
1-07-27 |
CLAMP-To
hold choke cable outer, black housing in proper position on carburetor. |
$1.43 |
$0.00 |
| 1-07-28 |
1-07-28 |
CLAMP
SCREW-For above clamp 1-07-27. |
$0.57 |
$0.00 |
| 1-07-29 |
1-07-29 |
CLAMP
WASHER-For above clamp 1-07-27. |
$0.28 |
$0.00 |
| 1-07-30 |
1-07-30 |
CLAMP
NUT-For above clamp 1-07-27. |
$0.35 |
$0.00 |
| 1-07-31 |
1-07-31 |
CHOKE
CAM ASSEMBLY-Fastens to bracket 1-07-25 and pivots back and forth as
choke cable is pulled in and out. |
$55.52 |
$0.00 |
| 1-07-32 |
1-07-32 |
RETURN
SPRING-Fastens to bracket 1-07-25 and cam 1-07-31 and returns choke cam
to "off" position when choke cable is pushed back in. |
$3.19 |
$0.00 |
| 1-07-33 |
1-07-33 |
PIVOT
SCREW FOR CHOKE CAM-Screws into right side of carburetor through main
bracket 1-07-25 and has shoulder which allows choke cam 1-07-31 to
rotate back and forth. |
$13.85 |
$0.00 |
| 1-07-34 |
1-07-34 |
SCREW-Fastens
and adjusts choke speed lever rod to correct idle speed increase when
pulling out choke. |
$0.75 |
$0.00 |
| 1-07-35 |
1-07-35 |
SCREW
FOR CHOKE CABLE-Holds metal wire end of choke cable on choke cam
1-07-31. |
$1.81 |
$0.00 |
| 1-07-36 |
1-07-36 |
INJECTION
PUMP PIPE-You'll spot this pipe immediately if you ever take the top of
your carburetor off to clean it. It looks like a fish hook sticking out
of the carburetor. |
$21.35 |
$0.00 |
| 1-07-37 |
1-07-37 |
RUBBER
O-RING SEAL-This important seal fits on the bottom of the injection pipe
1-07-36 and prevents gas leaks in carburetor. |
$3.79 |
$0.00 |
| 1-07-38 |
1-07-38 |
CARBURETOR
CHROME BALL-This miniature, polished chrome ball, about the size of BB,
goes in the hole in the carburetor where you stick the bottom of the
injection pipe 1-07-36. Remember to catch this ball if you ever turn
your carburetor over after you've removed the injection pipe for
cleaning. We get calls phone calls all the time about 'leaky"
carburetors, and all too often this ball rolled out, causing the
problem. |
$6.55 |
$0.00 |
| 1-07-39 |
1-07-39 |
ANTI-SIPHON
VALVE-Looks like small aluminum nail, fits inside jet 1-07-40. |
$4.61 |
$0.00 |
| 1-07-40 |
1-07-40 |
JET
FOR ANTI-SIPHON VALVE-If you have the top of your carburetor off, it
goes on the top of the right rear of the bottom half of your carburetor. |
$3.13 |
$0.00 |
| 1-07-41 |
1-07-41 |
EMULSION
TUBE-This is the only long tube with four holes in it which screws out
of sight into the bottom half of the carburetor. |
$11.93 |
$0.00 |
| 1-07-42 |
1-07-42 |
PILOT
AIR JET-This jet controls the amount of air mixing with the gas in your
carburetor. All Amphicar carburetors come equipped with pilot jets for
air mixing at sea level. Therefore, if you drive your Amphicar at high
altitudes, above 3,000 feet, you can probably inrcrease your performance
by installing a larger pilot jet. This jet is easy to replace and can be
removed or replaced in seconds on the outside of the carburetor. |
$12.65 |
$0.00 |
| 1-07-43 |
1-07-43 |
MAIN
JET-This jet in the bottom front side of the float bowl of the
carburetor regulates the amount of gas mixing in your carburetor.
Amphicar main jets are set for sea level operation. If you drive at high
altitudes, over 3,000 feet, you should install a smaller main jet to get
the very best performance. Also, see our information under pilot jet
1-07-42. |
$11.90 |
$0.00 |
| 1-07-44 |
1-07-44 |
PLUG
IN BACK OF CARBURETOR-You remove this plug to install main jet 1-07-43. |
$3.77 |
$0.00 |
| 1-07-45 |
1-07-45 |
GASKET
For plug 1-07-44. |
$0.65 |
$0.00 |
| 1-07-46 |
1-07-46 |
ECONOSTAT
JET-This is the only gray-colored metal jet in the Amphicar carburetor. |
$5.29 |
$0.00 |
| 1-07-47 |
1-07-47 |
CARBURETOR
FLOAT-Original Amphicar copper metal float. |
$15.94 |
$0.00 |
| 1-07-48 |
1-07-48 |
FLOAT
PIVOT ARM-Moves up and down on carburetor float. Rear of arm fits on rod
in slot at back of float bowl. |
$7.25 |
$0.00 |
| 1-07-49 |
1-07-49 |
FLOAT
SPINDLE ARM ROD-Looks like a nail without a head. Allows float pivot arm
to move up and down. |
$4.29 |
$0.00 |
| 1-07-50 |
1-07-50 |
NEEDLE
AND SEAT ASSEMBLY-This brass screw has a blunt needle which goes up and
down in the middle. It crews into the underside of the carburetor top
housing. |
$20.13 |
$0.00 |
| 1-07-51 |
1-07-51 |
GASKET-Seals
needle and seat on top housing. |
$0.65 |
$0.00 |
| None |
1-07-52a |
TOP
CARBURETOR HOUSING-For late type "IZ" Zenith carburetors only.
With the exception of the first 100 Amphicars produced, Amphicar
supplied two different carburetor models. The most popular was the Solex
brand on 1961 - 1967 early cars. In mid 1967, a Zenith "IZ"
was supplied. Look next to the threaded fuel fitting inlet on your
carburetor. If it says "30 PSEI",this top will not fit. If
your top housing has a coppercolored cap, about the size of a penny,
then most likely this top will replace yours. Call if not sure. Housing
is complete with choke place 1-07-53 and spindle rod 1-07-54. |
$97.58 |
$0.00 |
| 1-07-53 |
1-07-53 |
CHOKE
FLAPPER PLATE-When you pull out the choke cable, this
silver-dollar-sized plate closes off the top of the carburetor. It is
held on the choke spindle rod by two screws. |
$14.65 |
$0.00 |
| 1-07-54 |
1-07-54 |
CHOKE
PLATE SPINDLE ROD-The choke plate moves back and forth on this spindle
every time you operate the choke. The spindle sticks out of the right
side of the carburetor top housing where it moves against the choke cam
1-07-31. |
$30.60 |
$0.00 |
| 1-07-55 |
1-07-55 |
SCREW-To
hold choke plate 1-07-53 on spindle rod 1-07-54, two required. |
$1.44 |
$0.00 |
| 1-07-56 |
1-07-56 |
RETURN
SPRING-For choke plate spindle rod. |
$3.43 |
$0.00 |
| 1-07-57 |
1-07-57 |
MAIN
GASKET-Seals top of carburetor to bottom half. Fits carburetor with
1-07-42 pilot air jet. |
$4.50 |
$0.00 |
| 1-07-58 |
1-07-58 |
SCREW-Five
needed to fasten top of carburetor to bottom half. |
$2.87 |
$0.00 |
| None |
1-07-59 |
FLANGE-Heat
insulating flange fits between bottom of carburetor and carburetor base
plate 1-01-18. Two of paper gasket 1-07-61 are required to completely
prevent air leaks at bottom of carburetor. |
$6.88 |
$0.00 |
| None |
1-07-61 |
PAPER
INSULATING GASKET-Two required with one going on top of and one on
bottom of flange 1-07-59. Also, see gasket 1-01-27 for insulating the
bottom of carburetor base plate 1-01-18. |
$2.87 |
$0.00 |
| None |
1-07-62 |
RUBBER
VACCUM CONNECTOR HOSE-Original Amphicar. Fastens both ends of vacuum
line 1-06-30V, with one connector joining carburetor to vacuum line and
second connector joining vacuum advance to vacuum line. Two required. |
$5.49 |
$0.00 |
| None |
1-07-63S |
MINOR
CARBURETOR REPAIR KIT-Consists of the following part numbers:
1-07-57,50, |
$39.95 |
$0.00 |
| None |
1-07-63L |
MAJOR
CARBURETOR REBUILDING KIT-Consists of the following part numbers:
1-07-02, 05,07,08,12,20,32,36,37,38,39,40,41,42,43,46,50,51,53,56,57,
and two of 61. See descriptions above. For early carburetors using pilot
jet 1-07-42. |
$129.50 |
$0.00 |
